Danh mục

Model	C9136I-ROW
Software	● Cisco IOS ^® XE Software Release 17.7.1 or later
Supported wireless LAN controllers	● Cisco Catalyst 9800 Series Wireless Controllers (physical or virtual)
802.11n version 2.0 (and related) capabilities	● 4x4 MIMO with four spatial streams ● Maximal Ratio Combining (MRC) ● 802.11n and 802.11a/g ● 20- and 40-MHz channels ● PHY data rates up to 1.5 Gbps (40 MHz with 5-GHz and 20 MHz with 2.4-GHz) ● Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive) ● 802.11 Dynamic Frequency Selection (DFS) ● Cyclic Shift Diversity (CSD) support
802.11ac	● 8x8 downlink MU-MIMO with eight spatial streams ● MRC ● 802.11ac beamforming ● 20-, 40-, 80-, and 160-MHz channels ● PHY data rates up to 3.4 Gbps (8x8 80 MHz or dual 4x4 80+80 MHz on 5-GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) ● 802.11 DFS ● Cyclic Shift Diversity (CSD) support ● Wi-Fi Protected Access (WPA) 3 support
802.11ax	● 8x8 uplink/downlink MU-MIMO with eight spatial streams (5-GHz) ● 4x4 uplink/downlink MU-MIMO with four spatial streams (2.4 and 6-GHz) ● Uplink/downlink OFDMA ● TWT ● BSS coloring ● MRC ● 802.11ax beamforming ● 20-, 40-, 80-, and 160-MHz channels (6-GHz) ● 20-, 40-, 80-, 80+80-MHz (5-GHz) ● 20-MHz channels (2.4-GHz) ● PHY data rates up to 10.2 Gbps (4x4 160 MHz on 6 GHz, 8x8 80 MHz on 5-GHz, and 4x4 20 MHz on 2.4-GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) ● 802.11 DFS ● CSD support ● WPA3 support
Integrated antenna	● 2.4-GHz: Peak gain 4 dBi, internal antenna, omnidirectional in azimuth ● 5-GHz: Peak gain 5 dBi, internal antenna, omnidirectional in azimuth ● 6-GHz: Peak gain 6 dBi, internal antenna, omnidirectional in azimuth
Interfaces	● 2x 100M/1000M/2.5G/5G Multigigabit Ethernet (RJ-45) ● Management console port (RJ-45) ● USB 2.0 at 9W
Indicators	● Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors
Dimensions (W x L x H)	● Access point (without mounting brackets): ◦ 9.9 x 9.9 x 2.2 in. (25.1 x 25.1 x 5.6 cm)
Weight	● 3.6 lb. (1.65 kg)
Input power requirements	● 802.3bt Cisco Universal PoE (Cisco UPOE ^®), 802.3at Power over Ethernet Plus (PoE+) ● Cisco power injector, AIR-PWRINJ7= ● 802.3af PoE (only for configuration staging, all radios off)
		Catalyst 9136I
	PoE power consumption	2.4-GHz radio		5-GHz radio	6-GHz radio	Link speed	USB	Link Layer Discovery Protocol (LLDP)
	802.3bt (UPOE)	4x4		8x8	4x4	2x 5G	Y (9W)	47.3W
	802.3at (PoE+)	2x2		2x2	4x4	1x 2.5G	N	24.4W
	802.3af (PoE)	–		–	–	1x 1G	N	13.95W
	Note: Power required at the Power Source Equipment (PSE) will depend on the cable length and other environmental issues.
Environmental	● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) ● Nonoperating (storage) altitude test: 25˚C (77°F) at 15,000 ft (4600 m) ● Operating temperature: 32° to 122°F (0° to 50°C) ● Operating humidity: 10% to 90% (noncondensing) ● Operating altitude test: 40˚C (104°F) at 9843 ft (3000 m) Note: When the ambient operating temperature exceeds 40°C (104°F), the access point will shift from 8x8 to 4x4 on the 5-GHz radio, and uplink Ethernet will downgrade to a single 1G; however, the USB interface will remain enabled.
System memory	● 2048 MB DRAM ● 1024 MB flash
Available transmit power settings	2.4 GHz ● 23 dBm (200 mW) ● -4 dBm (0.39 mW)		5 GHz ● 26 dBm (400 mW) ● -1 dBm (0.79 mW)			6 GHz ● 23 dBm (200 mW) ● -4 dBm (0.39 mW) Note: In countries where use of the 6 GHz band is not allowed or there is no current software support, the 6 GHz radio will be disabled. The radio may be enabled with future software, once the product is certified to operate in 6 GHz for that country.