Danh mục

C9400-LC-48HN Cisco Catalyst 9400 Series 48-Port UPOE+ 5G multigigabit (RJ-45) Module for Cisco Catalyst C9404R, Cisco Catalyst C9407R and Cisco Catalyst C9410R.

Giá bán : Liên hệ để có giá tốt
Tình trạng : Còn hàng

Thông số kỹ thuật
Tài liệu liên quan

Module chuyển mạch Cisco Catalyst 9400 Series 48-Port UPOE+ 5G multigigabit (RJ-45) (C9400-LC-48HN)

Description	48-port, 100Mbps/1/2.5/5Gbps BASE-T Multigigabit Ethernet, IEEE802.3af, IEEE802.3at, and IEEE802.3bt compliant module supporting up to 90 W Cisco UPOE+ on each of its 48 RJ45 ports. Hardware ready for IEEE 1588/802.1as— A Precision Time Protocol (PTP) used for time synchronization across the network for video and audio applications. Supports IEEE802.3af / IEEE802.3at / IEEE802.3bt on all 48 ports, with DC disconnect. Supports Energy Efficient Ethernet (EEE) Supports PoE Cable Loss Management Supports PoE Emergency Shutdown based on 3-bit priority Has a built-in, front-facing, passive RFID tag that uses Ultra High Frequency (UHF) RFID technology and requires an RFID reader with compatible software. It provides auto-identification capabilities for asset management and tracking. The RFID tags are compatible with the Generation 2 GS1 EPC Global Standard and are ISO 18000-6C compliant. They operate in the 860- to 960-MHz UHF band. For more information, see Radio Frequency Identification (RFID) on Cisco Catalyst 9000 Family Switches. The following switching module features are configured in software. See the software configuration guide for more information: Provides per port power consumption measurement Enables you to specify maximum power consumption on every port Supports PoE Power Configuration The 7-slot (Catalyst 9407R switch) chassis has a maximum of 240 ports but can support up to 237 90W ports concurrently. The 10-slot (Catalyst 9410R switch) chassis has a maximum of 384 ports but can support up to 233 90W ports concurrently.
Per Slot Bandwidth	Per slot bandwidth depends on the supervisor module: 80 Gbps with C9400-SUP-1XL in 10-slot chassis or C9400-SUP-1. The over-subscription ratio is 3:1 120 Gbps with C9400-SUP-1XL in 7-slot chassis and 4-slot chassis. The over-subscription ratio is 2:1
Minimum / Maximum Port Density⁸	Catalyst 9404R Switch—48 / 96 Catalyst 9407R Switch—48 / 240 Catalyst 9410R Switch—48 / 384
Support and Restrictions	Can be installed in any non-supervisor module slot. Ensure that the chassis power supply configuration supports the PoE budget adequately. Use the Cisco Power Calculator for power budgeting estimates and to determine power supply requirements for a specific PoE configuration. Some legacy Cisco powered devices (like 7910, 7940, 7960 IP phones and AP350 wireless access points) are incompatible with Type 4 Power Supply Equipments (PSEs), as defined in the IEEE 802.3bt standard. If connected, the PSE reports a ‘Tstart’ or ‘Imax’ fault with each periodic attempt at providing power to the powered device. For continued use of these legacy Cisco powered devices, connect them to Cisco PoE+/UPOE PSEs. C9400-LC-48HN module is supported only on Cisco IOS XE Release 17.5.1 and later releases. Before inserting the module, ensure that the device software is Cisco IOS XE Release 17.5.1 or a later release. Before downgrading the software on the device from Cisco IOS XE 17.5.1 to earlier releases, ensure that you remove the C9400-LC-48HN module.