Danh mục

Model	AP-634 (S1G49A)
Wi-Fi radio specifications	• AP type: Indoor, tri radio, 2.4GHz, 5GHz and 6GHz (concurrent) 802.11ax 2x2 MIMO • 2.4 GHz radio: Two spatial stream Single User (SU) MIMO for up to 574 Mbps wireless data rate with 2SS HE40 802.11ax client devices • 5 GHz radio: Two spatial stream Single User (SU) MIMO for up to 1.2 Gbps wireless data rate with 2SS HE80 802.11ax client devices • 6 GHz radio: Two spatial stream Single User (SU) MIMO for up to 2.4 Gbps wireless data rate with 2SS HE160 802.11ax client devices • Up to 512 associated client devices per radio, and up to 16 BSSIDs per radio (limited to 4 for the 6GHz radio)
Wi-Fi antennas	• Two sets of two (female) RP-SMA connectors for external antennas (A0 & A1 corresponding with radio chains 0 and 1 for the 2.4GHz and 5GHz radios, and B0 & B1 corresponding with radio chains 0 and 1 for the 6GHz radio). Worst-case internal loss between radio interface and external antenna connectors: 1.0dB in 2.4GHz, 1.0dB in 5GHz and 1.0dB in 6GHz.
Other interfaces and features	• E0, E1: Two Ethernet wired network ports (RJ-45) - Auto-sensing link speed (100/1000/2500BASE-T) and MDI/MDX - 2.5 Gbps speed complies with NBase-T and 802.3bz specifications - PoE-PD: 48Vdc (nominal) 802.3at/bt PoE (class 4 or higher) - 802.3az Energy Efficient Ethernet (EEE) - Link aggregation (LACP) support between both network ports for redundancy and increased capacity • DC power interface: 12Vdc (nominal, +/- 5%), accepts 2.1mm/5.5mm center-positive circular plug with 9.5mm length • USB 2.0 host interface (Type A connector) - Capable of sourcing up to 1A/5W to an attached device • Bluetooth Low Energy (BLE5.0) and Zigbee (802.15.4) radio - BLE: up to 5 dBm transmit power (class 1) and -100 dBm receive sensitivity (125 kbps) - Zigbee: up to 5 dBm transmit power and -97 dBm receive sensitivity (250 kbps) - Integrated omnidirectional antenna with roughly 30 to 40 degrees downtilt and peak gain of 3.0 dBi • GNSS L1 (1575.42 MHz) receiver supporting GPS, Galileo, GLONASS, and BeiDou signal - Receive sensitivity: -160dBm (tracking) - Integrated omnidirectional antenna with roughly 30 to 40 degrees downtilt and peak gain of 3.6dBi • Advanced IoT Coexistence (AIC) allows concurrent operation of multiple radios in the 2.4 GHz band • Built-in Trusted Platform Module (TPM) for enhanced security and anti-counterfeiting • Visual indicators (four multi-color LEDs): for System (1x) and Radio (3x) status • Reset button: factory reset, LED mode control (normal/off) • Serial console interface (proprietary, micro-B USB physical jack) • Kensington security slot • Automatic thermal shutdown and recovery function
Power sources and power consumption	• The AP supports direct DC power and Power over Ethernet (PoE) on port E0 and/or E1 • When both DC and PoE power sources are available, DC power takes priority over PoE • When PoE power is supplied to both Ethernet ports, either port can be configured as the active power source • Inactive/standby PoE power sources can be used to deliver hitless failover • Power sources are sold separately • When powered by DC or 802.3bt (class 5) PoE, the AP will operate without restrictions. • When powered by 802.3at (class 4) PoE with the IPM feature disabled, the AP will disable the USB port. • Operating the AP with an 802.3af (class 3 or lower) POE source is not supported (except for AP staging). • With IPM enabled, the AP will start up in unrestricted mode but may dynamically apply restrictions depending on the available power budget and actual consumption. The feature restrictions and order in which these get applied are configurable. • Maximum (worst-case) power consumption (without/with a USB device attached): - DC powered: 20.7W/26.4W. - PoE powered: 23.8W/29.4W. - This assumes that up to 5W is supplied to the attached USB device. • Maximum (worst-case) power consumption in idle mode: 8.7W/14.2W (DC) or 11.7W/17.2W (PoE). • Maximum (worst-case) power consumption in deep-sleep mode: 1.1W (DC) or 1.9W (PoE).
Mechanical specifications	• Dimensions/weight (AP-635; unit without mount bracket): - 220mm (W) x 220mm (D) x 51mm (H) - 1300g • Dimensions/weight (AP-635; shipping): - 250mm (W) x 240mm (D) x 85mm (H) - 1650g
Environmental specifications	• Operating conditions - Temperature: 0C to +50C/+32F to +122F - Relative humidity: 5% to 95% - ETS 300 019 class 3.2 environments - AP is plenum rated for use in air-handling spaces • Storage conditions - Temperature: -25C to +55C / -13F to +131F - Relative humidity: 10% to 100% - ETS 300 019 class 1.2 environments • Transportation conditions - Temperature: -40C to +70C/-40F to +158F - Relative humidity: up to 95% - ETS 300 019 class 2.3 environments